Monday 30 September 2013

Novel White LED Torch

Although this design is reproduced directly from the manufacturer’s datasheets, its use in this application is rather novel. Originally intended for high-visibility LED bargraph readouts, here the LM3914 is used as the basis of a 10-step variable brightness current-regulated white LED torch! The circuit has only four components in the control and regulation circuit: R1, R2, VR1 and the LM3914. The circuit can be built directly on the pins of the LM3914 to produce a package not much bigger than the LM3914 itself. The LM3914 is set to operate in bargraph mode so that the LEDs light progressively as its input signal increases.

This signal comes from the wiper of VR1, which provides a variable voltage between 0V and the supply voltage to pin 5 of the LM3914. The internal resistor ladder network of the LM3914 has its low end (pin 4) connected to ground and the high end (pin 6) connected to the supply voltage via R2. The purpose of R2 is to give LED 10 a clear turn-on zone. Resistor R1 (620Ω) on pin 7 of IC1 sets the current through each LED to about 20mA. As VR1 is rotated from the 0V position (all LEDs off) to the supply voltage position (all LEDs on), the LEDs will progressively light. With all LEDs off, the circuit will draw about 5mA. With all LEDs illuminated, it will draw about 205mA and dissipate 307mW with a 4.5V supply.

Novel white LED torch circuit schematic

Editors note:

These are nominal figures only. Actual device dissipation will depend entirely on the input voltage and LED forward voltage. In use, we recommend that a resistor (R3) be inserted in series with the positive supply, chosen so that the LM3914’s dissipation is limited to about 500mW. Typically, this would be needed for supply voltages of 6V and higher. The inclusion of the resistor necessitates a 10μF decoupling capacitor across the supply rails.) By carefully selecting the LEDs, this torch can be as bright as 15,0000mCd while costing less than $20.
ContinueReading..

Saturday 28 September 2013

Switch Mode 555 Supply

This switch-mode power supply is built around a 555 timer IC. It provides a maximum output voltage of 40 V with a 12-V input voltage. The voltage can easily be set using a Zener diode, and it must be higher than the input voltage (the minimum output voltage is always 12 V). The NE555 is used in an unconventional way here. In the normal configuration, the output of the oscillator IC is low longer than it is high. With the configuration used here, the output can be high for a shorter time than it is low. The NE555 switches FET T1 on and off.When T1 is conducting, energy is stored in L1. When T1 stops conducting, this energy is transferred to C1 and C2 via Schottky diode D1, so the voltage on these capacitors rises.

The voltage is limited by Zener diode D2.If the voltage rises above the Zener voltage,the current through the Zener diode causes T3 to conduct. This reduces the voltage on pin 5 of the NE555, which in turn decreases the relative duration of the high level on pin 3. T1 thus conducts for a shorter interval, so less energy is stored in L1 and the output voltage is stabilised.Current limiting is provided by R6, R5 and T2. If the voltage across R6 is more than 0.6 V, T2 starts to conduct. This drives T3 into conduction, causing the voltage to decrease in order to limit the current.

C5 and R7 provide a soft-start effect.The value of R1 can range from 22 kΩ for an output voltage of 15 V to 10 kΩ for an output voltage of 40 V.For the sake of safety, limit the Zener voltage to a maximum of 40 V. T1 and T2 can be rated for a maximum of 50 V. The FET is not critical; you may already have one in your spare parts bin that can switch enough current. If the coil becomes warm,the core is too small or the wire is too thin.The Schottky diode is the only component that is actually critical. Do not use an ordinary diode, since it will become much to

hot. You’re bound to find a Schottky diode in an old computer power supply (just check for a forward voltage of 0.2 V on the diode range of your multimeter).The supply shown here can deliver approximately 200 W. The input supply voltage can range from 7 V to 15 V.Don’t forget that the maximum voltage the NE555 can handle is 15 V.Finally, this power supply is not short circuit proof. A slow-blow fuse on the 12-V side is recommended.

Author : Martijn Geel Copyright :elektor elector
ContinueReading..

Thursday 26 September 2013

LED Noughts And Crosses

Here’s a twist to the age-old game of noughts and crosses. Instead of pen and paper, it uses nine 10mm tri-colour LEDs arranged in a 3 x 3 grid. One player has nine red buttons while the other player has nine green, set out in identical grids. The aim, of course, is to make three LEDs in a row glow the same colour – red or green! Pushing a red button causes the LED in the equivalent position on the grid to glow red in colour. Likewise, pushing a green button lights the equivalent green LED.

LED noughts & crosses circuit schematic

If a player pushes a button for a LED that is already glowing red or green, then that LED changes to yellow, exposing the false move! All the LEDs are then turned off, ready for the next game, by pressing the "Clear" button. For simplicity, the circuit shows only one tri-colour LED and a pair of opposing buttons. This circuit fragment must be repeated another eight times to create a complete 3 x 3 grid. A brief press on a button fires the associated SCR and turns on the LED. The common (cathode) lead of all LEDs is connected to the 0V rail via the normally-closed contacts of the "Clear" pushbutton (S3).
ContinueReading..

Tuesday 24 September 2013

Optimised Semiconductor Noise Source

We have already published designs that use a transistor junction operating in Zener breakdown as a noise source. Anyone who has experimented with a reverse-biased transistor knows that the amplitude of the noise voltage generated in this manner is strongly dependent on the supply voltage. The variation between individual transistors is also rather large. An obvious solution is to use an adjustable supply voltage for the noise generator stage. A BC547B starts to break down at around 8V.

Circuit diagram :

Optimised Semiconductor Noise Sourcew

Optimised Semiconductor Noise Source Circuit Diagram

Using P1 and R1, you can adjust the voltage across T1 and R2 between 8 and 12V. C3 decouples the reduced supply voltage. An impedance buffer in the form of T2 and R3 is added to the circuit, to prevent the connected load from affecting the noise source. This buffer is powered directly from the 12-V supply. To adjust this circuit, connect the output to an oscilloscope. Then adjust P1 to obtain the highest signal amplitude, combined with the best ‘shape’ of the noise signal. The output voltage is approximately 300mVpp, and the current consumption is around 2mA.

Source : www.extremecircuits.net

ContinueReading..

Sunday 22 September 2013

12 Volt DC Fluorescent Lamp Driver

A number of people have been unable to find the transformer needed for the Black Light project, so I looked around to see if I could find a fluorescent lamp driver that does not require any special components. I finally found one in Electronics Now. Here it is. It uses a normal 120 to 6V stepdown transformer in reverse to step 12V to about 350V to drive a lamp without the need to warm the filaments.

12 Volt DC Fluorescent Lamp Driver circuit diagramParts:

C1 100uf 25V Electrolytic Capacitor
C2,C3 0.01uf 25V Ceramic Disc Capacitor
C4 0.01uf 1KV Ceramic Disc Capacitor
R1 1K 1/4W Resistor
R2 2.7K 1/4W Resistor
Q1 IRF510 MOSFET
U1 TLC555 Timer IC
T1 6V 300mA Transformer
LAMP 4W Fluorescent Lamp
MISC Board, Wire, Heatsink For Q1

Notes:
  1. Q1 must be installed on a heat sink.
  2. A 240V to 10V transformer will work better then the one in the parts list. The problem is that they are hard to find.
  3. This circuit can give a nasty (but not too dangerous) shock. Be careful around the output leads.
ContinueReading..

Friday 20 September 2013

1995 KLR650 Dual Sport Motocross Wiring Diagram

1995 KLR650 Dual Sport Motocross Wiring Diagram

The Part of 1995 KLR650 Dual Sport Motocross Wiring Diagram: instrument cluster, ignition switch,
right front turn signal, front brake light switch, starter button, engine stop switch, water temperature sender, meter light, high beam indicator light, neutral indicator light, fan switch, cooling fan, voltage regulator rectifier, turn signal relay, brake tail light, license light, starter circuit relay, battery, chassis ground, starter relay, CDI, neutral switch, magneto, headlight switch, dimmer switch, turn signal switch, horn button, stand switch, ignition pick up coil, chassis ground, horn, headlight, turn signal.
ContinueReading..

Tuesday 10 September 2013

An LCD Clock Kit Suitable for Beginners with Open Source Arduino Firmware

Simpleclock is an easy to assemble attractive 4-digit 7-segment LED display clock with temperature and alarm function. It is available in three display colors: Red, Blue and White. It comes as a kit of through-the-hole parts and can be soldered by any person with basic soldering experience. An attractive acrylic stand is included.


ContinueReading..